How to distinguish the number of layers of 亚娱体育官方网站 multilayer board

How to identify the number of layers of 亚娱体育官方网站 multilayer board? Here's how to identify them!

亚娱体育官方网站

The 4 layers of the board are the 1st and 4th layers for wiring, and the other layers are used for other purposes (ground wire and power supply)

The auxiliary signal layer is added to layer 6 and 8

Each layer of the 亚娱体育官方网站 board problem has its own role. The main signal layer of the power layer, the auxiliary signal layer, and the ground layer are the same in general design

The base plate of 亚娱体育官方网站 itself is made of insulating and heat-insulating materials that are not easy to bend. The SMAll circuit material that can be seen on the surface is copper foil. Originally, the copper foil was covered on the entire 亚娱体育官方网站, but some parts were etched during the manufacturing process, and the remaining parts beCAMe retICular small

The line is up. These lines are calLED wires or wiring, and are used to provide circuit

 connection of parts on 亚娱体育官方网站. Usually, the color of 亚娱体育官方网站 is green or brown, which is the color of solder resist paint. It is an insulating protective layer, which can protect copper wires and prevent parts from being welded to incorrect places.

Now the motherboard and the graphics card are all multilayer boards, which greatly increases the area of 亚娱体育官方网站 wiring. More single or double sided wiring boards are used for Multilayer boards, and a layer of insulating layer is placed between each layer of boards and then pressed together. The number of layers of a 亚娱体育官方网站 board represents several independent wiring layers. Usually, the number of layers is even and includes the outermost two layers. Common 亚娱体育官方网站 boards are generally 4-8 layers. The number of layers of many 亚娱体育官方网站 boards can be seen by viewing the section of 亚娱体育官方网站 board. But in fact, no one can have such good eyesight. So, let's teach you another method.

The circuit connection of multilayer boards is through the buried hole and blind hole technology. The motherboard and display card mostly use 4-layer 亚娱体育官方网站 boards, while some use 6-layer, 8-layer, or even 10 layer 亚娱体育官方网站 boards. To see how many layers a 亚娱体育官方网站 has, you can identify them by observing the pilot hole. Because the four layers of boards used on the motherboard and display card are the first and fourth layers of wiring, and the other layers are used for other purposes (ground wire and power supply). Therefore, like the double-layer board, the pilot hole will pierce the 亚娱体育官方网站 board. If some pilot holes appear on the front of the 亚娱体育官方网站, but cannot be found on the back, it must be 6/8 layers. If the same pilot holes can be found on both the front and back of a 亚娱体育官方网站, it is naturally a 4-layer board.

Tip: Hold the main board or display to the light source. If the position of the guide hole can transmit light, it means it is a 6/8 layer board; On the contrary, it is 4-layer plate.

亚娱体育官方网站 is short for print circuit board. That is, printed circuit board. The conductive copper sheet is attached to the base plate of the insulating material for circuit connection. These circuit connections can be on the front, back, or even in the middle of the substrate. Generally, 亚娱体育官方网站 with circuit layers larger than 2 layers (i.e. front and back) is called multilayer board.

亚娱体育官方网站 can be divided into single-layer board (single panel) with circuit printed on one side only, double-sided board with circuit printed on both upper and lower sides, and multilayer board with multilayer circuit sandwiched in the middle.

Professional 亚娱体育官方网站 manufacturers and 亚娱体育官方网站 design and solution service providers focus on the development of 亚娱体育官方网站 industry and are trustworthy.